Why does kenmore refrigerator leak water

Use hot water to clear the drain hole. Keep working the hot water into the hole and wiping the excess water. This can take quite awhile, depending on how deep the ice is. This will need to be done until you get a good water flow down to the bottom drain pan. With the drain system clear, water should stop leaking in the refrigerator. If you would like more assistance, additional details will be needed.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services. Safety Notice : Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs.

Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. I did this yesterday and it worked Great! Want to get updates on new answers? Repair and disassembly guides for food cooling appliances including refrigerators, freezers and fridge-freezers. Bryan Hooten. I have a Kenmore refrigerator model , the water dispenser drips water. I have replace the water valve on the back of the refrigerator and also have ran many gallons of water through it to get the air bubbles out of the system.

There is also a filter that I added on a few years back and it has good water pressure coming from it.

Any ideas what could cause this drip? Refrigerator is at least 15 years old and is a side by side. LadyTech ladytech. Usually when the water dispenser is dripping water, you can look up and see water dripping from the plastic water line above where you put your glass.

A water inlet valve is usually the cause. Minerals in the water can pass through the filter and cause the valve not to close completely.

Thus, you can have a drip or even a flood. It not worth the risk of having it fail completely and stick completely open during the night. No one likes to wake up to a flooded kitchen. The valve has two solenoids. One for water dispenser and one for the ice maker. Unplug the unit and the water off at the wall before removing the access panel. Easy part to replace. If the drain pan is dirty and begins to leaking, the liquid will be dark-colored.

The pan may be overflowing. In this case, take it out, clean it, and reinstall it. Check the leak and if it looks oily then it is most likely from the compressor.

If the compressor is leaking, call a repair technician to take a look at it. Replacing or repairing the compressor may be very expensive while getting a new refrigerator may be more cost-effective.

The most common reason your Kenmore refrigerator is leaking from the water dispenser is trapped air in the water line. This is because, when air is trapped in the water line, the pressure will build up and cause water to drip out of the dispenser. To stop the leak, the trapped air has to be released. Release the trapped air by doing the following:. Note to always do this after each filter change. This is because the air tends to get trapped in the water line during a filter change.

Also, if the water dispenser keeps on leaking, try out the solutions in the section above. You can also read this article for more information on this topic. The water inlet valve supplies water to the whole refrigerator from the main water supply. To shut off, the inlet valve requires about 20 psi. However, if the psi is below 20, the inlet valve will not close properly.

Also, if the valve is defective, it may stay open and cause water to leak. The water inlet valve has to be replaced in this case. Step 2: Adjust the refrigerator so you can have access to the back. Take out the nuts holding the water line in place. Step 3: With a Philip screwdriver, remove the screws holding the back panel in place.

Then take off the back panel. Take out the blue tube, and then the mounting bracket, and finally the remaining water lines. Now the valve is completely free, take it out.

Step 5: Get the new inlet valve and connect the water lines and bracket to it. Finally, reassemble the refrigerator by doing the steps in reverse. If your Kenmore refrigerator is leaking water from the ice maker then the first place you have to check is the water inlet valve. If the water inlet valve is leaking, the water may come out from the ice maker. In this case, the inlet has to be replaced, the above section contains instructions for how to replace your Kenmore refrigerator inlet valve. If the water inlet valve is not the cause of the leak, then a part of the ice maker assembly may be faulty.

The fill tube is the most common cause of a leaking ice maker. So check and replace that if necessary. Step three: Take out the ice maker to gain access to the fill tube. Take off the extension on the fill tube. Step five: Go to the front of the refrigerator and take out the fill tube. Remove the gasket on the tube and place it on the new fill tube.

Step six: Install the fill tube and reassemble your appliance by doing the steps in reverse order. If the ice maker keeps leaking after this, then some other part of the assembly may be faulty. At this point, we advise that you take out the whole ice maker assembly and replace it with a new one.